Cardboard boxes moving on conveyor belts inside a large warehouse or distribution center with industrial lighting.

Freight Elevator vs. VRC Lift: Which One a Warehouse Needs

A freight elevator is built to ASME A17.1, the elevator safety code, and may carry the operator and the people handling the freight. A vertical reciprocating conveyor, usually shortened to VRC lift, is built to ASME B20.1, the conveyor safety standard, and carries material only. That difference in rider rules drives most of the gap in building work, permitting, and price between the two machines. A warehouse or plant that only needs pallets, carts, or totes moved to a mezzanine or second floor can meet that need with a VRC and skip the elevator code entirely.

The Code Decides Which Machine It Is

Both machines raise a platform between fixed levels inside a guarded path. The elevator code assumes a person may be inside the car, so a freight elevator needs a car enclosure, a code-built hoistway, door interlocks, car safeties, and a pit and overhead sized to protect anyone working in the shaft.

A VRC is classed as a conveyor. PFlow Industries, which built the first VRCs in 1977, states that the national codes were changed in 1981 to exempt material-only vertical conveyors from the elevator rules. A VRC has guide columns, a carriage, and a hydraulic or mechanical drive, with gates and enclosure panels that keep people out of the travel path. Nobody rides it, and the controls sit outside the carriage at each level.

Freight Elevator Loading Classes

A17.1 sorts freight elevators by how the load gets onto the platform. Class A covers general freight loaded by hand or hand truck, where no single piece weighs more than a quarter of the rated load. Class B covers motor vehicles. Class C1 lets an industrial truck ride with its load, provided truck and load together stay within the rated capacity. Class C2 allows the platform to carry up to 150 percent of rated load while a forklift places the freight, and the forklift backs off before the car moves. Class C3 covers other concentrated loads that stay within the rating.

The class has to be named before the elevator is engineered, because it sets the platform, sill, and door design. A warehouse freight elevator loaded by forklift is a Class C machine, and a Class A quote will not cover that duty.

What A VRC Lift Is Built To Do

A VRC is sized around the load itself: its weight, its footprint, how it arrives, and how many times an hour it moves. PFlow's published range includes carriages as small as 30 by 30 inches and as large as 60 by 60 feet, with vertical travel starting at 4 feet and passing 200 feet. Loads can roll on by pallet jack or cart, be set down by forklift, or feed in on powered conveyor.

Power and Motion's recent mezzanine lift installations include a 6,000 lb unit serving a mezzanine storage level and a 15,000 lb unit with 15 feet of travel. A VRC can sit at the edge of a steel mezzanine system, pass through a floor opening, or, per PFlow, go into an unused elevator shaft.

Hydraulic And Mechanical VRC Limits

Hydraulic VRCs suit two-level work at low cycle counts. PFlow rates its hydraulic units for loads up to 6,000 lb at 10 cycles per hour and 100 cycles per day, with vertical rise up to 22 feet. The two-post PFlow 21 Series carries up to 6,000 lb and the D Series up to 3,000 lb, both depending on carriage size.

Mechanical VRCs cost more and take over where hydraulic units stop: three or more levels, continuous cycling, and heavier loads. PFlow lists the M Series at 10,000 lb. The F Series is engineered to the load, and its four-post frame leaves every side of the carriage open for loading.

Building Work, Permits, And Inspection In Georgia

Georgia regulates elevators under Chapter 120-3-25 of the Safety Fire Commissioner's rules. A new freight elevator needs a construction permit, a certified elevator contractor, and an acceptance inspection, and it runs afterward under an operating permit with a current inspection certificate. The building work usually includes a pit, a rated hoistway, and machine space.

A VRC is installed as conveyor equipment under B20.1, and PFlow states that its VRCs cost less than elevators to install, operate, and maintain. Local plan review still applies, particularly where the lift passes through a floor. Power and Motion's industrial permitting service prepares that submittal, and the same crews return for lift inspection and service after startup.

Choosing Between A Freight Elevator And A VRC

A freight elevator is the right machine when a person has to travel with the load, or when a forklift has to ride between floors under Class C1. A VRC fits when the load travels alone, which is the case for pallets, carts, and totes headed to a mezzanine or second-floor storage level.

The selection inputs are the same for either machine: heaviest load, platform size, vertical travel, number of levels, cycles per hour, and loading method. Power and Motion designs, sells, and installs PFlow VRCs across Atlanta, South Georgia, and the Southeast. Call 770-529-0418 with the load weight, platform size, and travel height to have a VRC lift quoted.

Link copied to clipboard!